Home › Hot Water Repairs Rowville
Plumber testing the element of an outdoor electric hot water cylinder with a multimeter, access cover removed
Hot water faults · Rowville VIC 3178

Hot Water Repairs Rowville

Cold shower this morning, water around the base of the cylinder or a relief valve that never stops dripping? Element, solar and heat pump units are all repaired across Rowville. Ring 03 9088 0246.

  • Licensed and insured
  • Based in Rowville 3178
  • Cost agreed before work
  • Urgent call-outs
Licensed and insuredVictorian plumbing licences, public liability cover, compliance certificates lodged
Cost agreed firstWe find the cause and talk you through the price before any work starts
Fixed on the first visitVans stocked with drain gear, cameras, valves, hoses and hot water parts
Rowville basedShort drives to Stud Park, Lysterfield, Scoresby, Knoxfield and Wheelers Hill

Hot water problems we fix

Hot water faults tend to show up in a handful of ways. Knowing which one you have helps us bring the right parts and gets your hot water back sooner.

  • No hot water at all
  • Water that is warm but never properly hot
  • Hot water that runs out much faster than it used to
  • A relief valve dripping or pouring water
  • Water leaking from the cylinder, pipes or fittings
  • The hot water circuit tripping the power
  • Rusty or discoloured water from the hot taps
  • Banging, rumbling or hissing noises from the unit
  • Hot water that is scalding hot or fluctuates in temperature

We repair electric storage systems, solar hot water with electric boosting and heat pump systems. Many of the faults have straightforward fixes, and we will always check whether a repair makes sense before talking about replacement.

Hot water in Rowville homes

Rowville's housing boom in the eighties and nineties left many homes with similar hot water arrangements. Electric storage cylinders, often outside against a wall or in the laundry, and solar systems with collectors on the roof were both popular. Over the years many of those original units have been replaced, some more than once, and more households are now switching to heat pumps.

What that means in practice is that a lot of Rowville hot water units are between ten and twenty years old. That is the age range where elements fail, thermostats drift, valves wear out and, eventually, the cylinder itself starts to corrode. Our guide on hot water unit lifespan explains what to expect at each stage.

Common faults and what we do about them

No hot water

The first thing to check is the switchboard. If the hot water circuit has tripped, reset it once. If it trips again, leave it off and ring us, because a tripping circuit usually means a faulty element or a wiring problem, and it should not be reset over and over.

If the power is on and there is still no hot water, likely causes include:

  • A failed heating element. Elements burn out with age, particularly in areas with hard water or high mineral content. We test the element with a multimeter and replace it if it has failed.
  • A faulty thermostat. The thermostat tells the element when to switch on and off. If it fails, the element may not heat at all, or may overheat and trip the safety cut-out.
  • A tripped over-temperature cut-out. This safety device switches off the element if the water gets too hot. It can be reset, but if it trips again there is usually a thermostat fault behind it.
  • Off-peak timing issues. Some electric systems are on an off-peak tariff and only heat at night. If the household is using more hot water than the cylinder holds, it may run out during the day. We can check the setup and suggest options.

Lukewarm water

If the water is warm but not hot, the thermostat may be set too low or failing, one element in a twin-element system may have failed, or a tempering valve may be letting too much cold water through. On solar systems, a failed booster element or a fault in the solar circuit can cause lukewarm water in winter. We check each component and replace what has failed.

Hot water running out quickly

If you used to have plenty of hot water and now it runs out after one shower, the cylinder may be heating only partly, the element may have scaled up, or the household's needs may have outgrown the unit. A family that has grown from two to five people may simply need a bigger system. We work out which and explain the options.

Dripping or pouring relief valve

Each storage cylinder carries a valve that lets out water if temperature or pressure climbs too high. It is a safety device that opens to release water if the pressure or temperature inside the cylinder gets too high. A small drip during heating can be normal, because water expands as it heats. A constant drip, a steady stream or a valve that lets go suddenly is not normal.

Common causes are a worn relief valve, high mains pressure, a faulty pressure limiting valve or an expansion control valve that needs attention. Rowville's mains pressure is high in some lower-lying streets, and that can push a relief valve to keep opening. We test the pressure, replace worn valves and fit or replace a pressure limiting valve where needed. See water pressure problems.

Relief valves should be checked regularly. Lifting the lever gently for a few seconds every six months helps keep the valve working. If it does not reseal afterwards, ring us.

Leaking cylinder

If water is leaking from the cylinder itself, rather than from a valve or pipe fitting, the inner tank has usually corroded through. Unfortunately, a leaking cylinder cannot be repaired and needs to be replaced. We confirm where the leak is coming from first, because a leaking fitting or valve can look like a cylinder leak and is a much simpler fix.

Rusty water

Rusty or discoloured water from the hot taps but not the cold usually means corrosion inside the cylinder. Storage cylinders have a sacrificial anode, a metal rod that corrodes instead of the tank. Once the anode is used up, the tank itself starts to corrode. If caught early, replacing the anode can extend the life of the cylinder. If the tank is already corroding badly, replacement is the more sensible option.

Noisy hot water unit

Rumbling or popping sounds often come from sediment build-up in the bottom of the cylinder. Hissing can come from a relief valve or a leak. Banging in the pipes when taps are turned off, called water hammer, is often related to high pressure. We diagnose the noise and fix the cause.

Water too hot or temperature fluctuating

Hot water delivered to bathrooms in Victoria must be limited to a safe temperature, usually 50°C, to prevent scalding. This is done with a tempering valve that mixes hot and cold water. If the water at the bathroom tap is too hot, or it swings between hot and cold, the tempering valve may be faulty or blocked. Tempering valves have a service life and should be checked every few years. Our guide to hot water temperature and scald rules explains why this matters.

Solar hot water repairs

Solar hot water was a popular choice in Rowville, with collector panels on the roof heating water that is stored in a tank, either on the roof or on the ground. When solar systems fail, common causes include:

  • Failed booster elements that leave the system unable to heat on cloudy days
  • Faulty controllers or pumps on split systems with a ground-mounted tank
  • Leaking collectors or roof pipework
  • Frost damage in older systems without frost protection
  • Faulty valves on the tank or collectors

We repair the electric and plumbing side of solar hot water systems, including boosters, valves, pipework and tanks. Where a system is old and needs several repairs, we will give you an honest view of whether repair or replacement makes more sense.

Heat pump repairs

Heat pump systems work like a refrigerator in reverse, using a fan and compressor to draw heat from the air into the water. They are very efficient and increasingly common in Rowville. When a heat pump stops heating properly, common faults include blocked air filters or fins, fan problems, faulty sensors and leaking valves. We check and repair the plumbing side of heat pump systems and work with the manufacturer on warranty issues. See heat pump hot water.

Repair or replace?

This is the question we get asked most about hot water. Our approach is to give you a straight answer based on what we find.

Repair usually makes sense when:

  • The cylinder is not leaking
  • The unit is less than ten years old or still in good condition
  • The fault is a single component such as an element, thermostat or valve

Replacement usually makes sense when:

  • The cylinder itself is leaking
  • The unit is well past its expected life and showing several problems
  • The household's hot water needs have outgrown the system
  • Power bills for hot water are high enough that a more efficient unit would repay itself

If replacement is the right call, we explain the options, including electric storage and heat pump systems, and can usually supply and fit a new unit quickly. See hot water replacement.

Hot water safety

A few safety points are worth knowing.

  • Never block or cap a relief valve, even if it drips. It protects the cylinder from bursting.
  • Do not reset a tripping circuit over and over. A circuit that keeps tripping has a fault that needs checking.
  • Keep the area around the unit clear so it can be accessed and inspected.
  • Check the tempering valve every few years so bathroom water stays at a safe temperature.
  • If water is leaking heavily, turn off the power to the unit at the switchboard and the cold water isolation valve on the inlet pipe, then ring us.

Our hot water repair process

  1. You ring 03 9088 0246. We ask about the unit, its age and what is happening, so we bring the right parts.
  2. We inspect and test. On site we check the power, element, thermostat, valves and cylinder, and find the cause.
  3. We explain the options. You hear what is wrong, what it will cost to repair and whether replacement is worth considering.
  4. We fix it. Most repairs are done on the first visit with parts from the van.
  5. We test and tidy up. We check the system is heating properly, the valves are working and the delivery temperature is safe.

Hot water repairs in nearby suburbs

As well as Rowville, we repair hot water systems in Lysterfield, Scoresby, Knoxfield, Ferntree Gully, Wheelers Hill, Mulgrave, Dandenong North and Endeavour Hills. Ring 03 9088 0246 to arrange a visit.

Electric, solar and heat pump: different faults

Each type of hot water system fails in its own way, so we start by working out which one you have and how old it is.

Electric storage units are the most common in Rowville. The usual faults are a failed heating element, a thermostat that has stopped switching, a tripped over-temperature cut-out or a circuit that keeps tripping at the switchboard. These are often repairable in one visit if the cylinder itself is sound.

Solar systems, either roof-mounted or split with a ground-level tank, have extra parts that can fail: the circulating pump, the controller, the sensors and the collector panels. Many have an electric booster, so a solar system with no hot water can be a booster fault rather than a solar one.

Heat pumps work like a reverse air conditioner, pulling heat from the outside air. Faults include fan problems, refrigerant issues, iced-up coils in cold snaps and failed backup elements. Some faults need a refrigeration technician, and we will tell you if that is the case.

When the relief valve drips

A small drip from the pipe connected to the top of the cylinder is often normal while the unit heats, because water expands. Steady running water, or a valve that drips constantly even when the unit is not heating, usually means the valve needs replacing or the water pressure coming in is too high. Both are simple to check. Never block or cap the relief valve drain: it is a safety device that stops the cylinder from overpressurising.

What to check before you ring

Look at the switchboard for a tripped hot water circuit, check whether the unit's isolation switch is on, and look for water around the base of the cylinder. Note the brand and age from the label. That information helps us bring the right parts.

Included

What you get with hot water fault finding

Diagnosis
We trace the fault with the right gear (camera, locator, thermal imager, gauge) and show you what we found
Your price
Talked through on site before we start, and set out in writing for larger work
Who does it
A Victorian licensed plumber, insured, with the licence class the job calls for
Parts
WaterMark approved fittings and fixtures, fitted to the Australian Standards
Records
A compliance certificate where the law needs one, and before and after photos on request
Finish
Repair tested in front of you, floors and benches wiped down, old parts gone with us
Questions we hear

Hot Water Fault Finding in Rowville: your questions

Why do I have no hot water?

Check whether the hot water circuit has tripped at the switchboard. If it has, reset it once. If it trips again or there is no obvious cause, the element, thermostat or cut-out may have failed. Ring us to test it.

Is a dripping relief valve normal?

A small amount of water during heating can be normal. A constant drip or steady flow is not, and usually means a worn valve or high water pressure.

Can a leaking hot water cylinder be repaired?

If the leak is from the tank itself, no. The cylinder needs replacing. If the leak is from a valve, pipe or fitting, it can usually be repaired.

How long does a hot water system last?

Electric storage cylinders often last ten to fifteen years, depending on water quality, maintenance and usage. Heat pumps and solar systems vary. Regular checks can help extend their life.

Do you repair solar hot water systems?

Yes. We repair boosters, valves, pipework and tanks on solar hot water systems, and advise when replacement makes more sense.

What temperature should my hot water be?

Water stored in the cylinder must be kept at least 60°C to prevent bacteria. Water delivered to bathrooms is usually limited to 50°C by a tempering valve to prevent scalding.

Why is my hot water rusty?

Rusty hot water usually means the cylinder is corroding inside. If caught early, replacing the anode can help. If corrosion is advanced, replacement is usually the better option.

How quickly can you fix my hot water?

Many repairs are done the same day with parts from our van. If a replacement is needed, many common units can be supplied and installed within a day or two.

Book or ask for a quote

Send us the details

Tell us about the job and a licensed Rowville plumber will ring you back. For a flood, a burst pipe or an overflowing sewer, skip the form and ring 03 9088 0246.

03 9088 0246

We do not publish a price list, because no two jobs are the same. You will know the cost before any work begins.







    What to expect

    How a Rowville Plumbing job works

    1. Step 1Tell us the problem

      Ring or send the form with what has gone wrong and where. A photo of the leak, the drain or the hot water label means we turn up with the right parts.

    2. Step 2Diagnosis and price

      We track down the cause, show you what we found and give you the cost. Nothing gets pulled apart until you say go.

    3. Step 3Repair and test

      The work is done to the Victorian plumbing rules and Australian Standards, then tested in front of you. Regulated work gets a compliance certificate.

    4. Step 4Clean up and check in

      Floors and benches are left as we found them, old parts leave with us, and on bigger jobs we ring a few days later to make sure all is well.

    Where we work

    Rowville, Stud Park and the suburbs around Lysterfield

    We are based in Rowville, between EastLink and the Lysterfield hills, so most jobs are a few minutes from Stud Park. From here it is a quick run up Stud Road to Knoxfield and Scoresby, east to Lysterfield and Ferntree Gully, across Wellington Road to Wheelers Hill and Mulgrave, and south over Police Road to Dandenong North and Endeavour Hills. Somewhere else nearby? Ring 03 9088 0246 and ask.

    Plumbing problem in Rowville?

    Talk to a licensed local plumber today. You will know what is wrong and what it costs before we start.