
Water Pressure Problems Rowville
Shower barely trickling, pipes banging every time a tap shuts or a relief valve that never stops dripping? We measure your water pressure and fix the cause, not just the symptom. Ring 03 9088 0246.
- Licensed and insured
- Based in Rowville 3178
- Cost agreed before work
- Urgent call-outs
Low water pressure
Low pressure makes showers frustrating, slows down filling the bath or kettle and can stop appliances like dishwashers working properly. Common causes include:
- A partly closed meter valve or isolation valve
- A faulty pressure limiting valve that has failed in a partly closed position
- A leak in the water service or internal pipes
- Corroded or scaled pipes, particularly older galvanised steel
- Blocked aerators or showerheads clogged with mineral deposits
- Undersized pipework for the number of fixtures
- A problem in the street supply
If low pressure affects only one tap or shower, the problem is likely in that fixture, such as a blocked aerator, a faulty mixer cartridge or a blocked showerhead. If the whole house is affected, the cause is more likely the meter, the pressure limiting valve, a leak or the supply.
High water pressure
High pressure might sound like a good thing, but it puts strain on every part of your plumbing. Signs include:
- Banging pipes when taps close, known as water hammer
- Taps and toilet valves wearing out quickly
- Flexible hoses failing early
- A hot water relief valve that drips constantly
- Water spraying hard from taps when first turned on
- Leaks at joints and fittings
Parts of Rowville, particularly lower-lying streets, can have mains pressure well above what household plumbing is designed for. That is why a pressure limiting valve is often fitted near the meter. If yours was never fitted, or has failed, high pressure may be shortening the life of your taps, hoses and hot water system.
Measuring pressure
The first step is always to measure. A gauge goes on the garden tap closest to the meter for a static reading, then we check flow at the shower, kitchen and laundry. That tells us whether pressure is too low, too high or fluctuating, and helps narrow down the cause.
Pressure limiting valves
A limiting valve drops street pressure to a level household fittings can live with. Victorian plumbing rules require one where mains pressure exceeds a set limit, and they are commonly fitted on new hot water installations.
Like any valve, a pressure limiting valve can fail. It might stick open, letting high pressure through, or partly closed, restricting flow. We test, replace and adjust pressure limiting valves.
Water hammer
Water hammer is the loud bang you hear when a tap or appliance valve closes quickly. The moving water stops suddenly, and the shockwave travels through the pipes. As well as being noisy, it can loosen pipe fixings and damage joints over time.
Fixes include reducing mains pressure with a pressure limiting valve, securing loose pipes, and fitting water hammer arrestors near appliances with quick-closing valves such as washing machines and dishwashers.
Showerhead and aerator issues
Mineral deposits can block showerheads and tap aerators, reducing flow. Cleaning or replacing them is often a quick fix. If you have a low-flow showerhead and find the pressure disappointing, we can suggest efficient models that still give a good shower.
Our process
- We measure static pressure and flow.
- We check the meter valve, pressure limiting valve, pipework and fixtures.
- We identify the cause and explain it.
- We give you the cost of fixing it before we start.
- We fix it, whether that is a new pressure limiting valve, a leak repair, new pipework or fixture repairs.
- We retest to confirm pressure is right.
Water pressure help in nearby suburbs
We diagnose and fix water pressure problems across Rowville, Lysterfield, Scoresby, Knoxfield, Ferntree Gully, Wheelers Hill, Mulgrave, Dandenong North and Endeavour Hills.
Pressure that changes through the day
If your pressure is fine early in the morning but weak in the evening, the cause may be high demand in the street rather than a fault in your home. If it is always weak, or only weak at one tap, the problem is more likely inside your property. Testing at the meter tells us which.
Too much pressure
High pressure can be just as much of a problem as low pressure. It strains taps, hoses, toilet valves and hot water units, causes banging pipes and can shorten the life of appliances.
What you get with low or high water pressure
- Diagnosis
- We trace the fault with the right gear (camera, locator, thermal imager, gauge) and show you what we found
- Your price
- Talked through on site before we start, and set out in writing for larger work
- Who does it
- A Victorian licensed plumber, insured, with the licence class the job calls for
- Parts
- WaterMark approved fittings and fixtures, fitted to the Australian Standards
- Records
- A compliance certificate where the law needs one, and before and after photos on request
- Finish
- Repair tested in front of you, floors and benches wiped down, old parts gone with us
Low or High Water Pressure in Rowville: your questions
Why is my water pressure suddenly low?
A failed pressure limiting valve, a leak, a partly closed valve or a street supply problem are common causes. If neighbours are also affected, check with South East Water.
What causes banging pipes?
Usually water hammer, caused by quick-closing valves and high pressure. A pressure limiting valve and pipe fixings often fix it.
Is high water pressure a problem?
Yes. It wears out taps, hoses, toilet valves and hot water systems faster and can cause leaks.
Do I need a pressure limiting valve?
If your mains pressure is high, yes. We can measure it and tell you.
Why is only my shower low pressure?
The showerhead may be blocked, the mixer cartridge faulty or the pipework to that bathroom restricted.
Can you increase my water pressure?
We can fix causes of low pressure such as faulty valves, leaks and blockages. If the street supply is low, a pressure pump may be an option.
Before you call, read this
Send us the details
Tell us about the job and a licensed Rowville plumber will ring you back. For a flood, a burst pipe or an overflowing sewer, skip the form and ring 03 9088 0246.
We do not publish a price list, because no two jobs are the same. You will know the cost before any work begins.
How a Rowville Plumbing job works
- Step 1Tell us the problem
Ring or send the form with what has gone wrong and where. A photo of the leak, the drain or the hot water label means we turn up with the right parts.
- Step 2Diagnosis and price
We track down the cause, show you what we found and give you the cost. Nothing gets pulled apart until you say go.
- Step 3Repair and test
The work is done to the Victorian plumbing rules and Australian Standards, then tested in front of you. Regulated work gets a compliance certificate.
- Step 4Clean up and check in
Floors and benches are left as we found them, old parts leave with us, and on bigger jobs we ring a few days later to make sure all is well.
Other plumbing work we do in Rowville
- Urgent Plumbing Call-Outs
- Blocked Drain Clearing
- Hot Water Fault Finding
- New Hot Water Systems
- Heat Pump Installation
- Burst and Split Pipes
- Dripping Taps and Mixers
- Toilet Fixes and New Suites
- Blocked Toilet or Sink
- Hidden Leak Detection
- CCTV Drain Inspection and Relining
- Stormwater Pits and Drains
- Ensuite and Bathroom Renovations
- Gutter and Downpipe Replacement
Rowville, Stud Park and the suburbs around Lysterfield
We are based in Rowville, between EastLink and the Lysterfield hills, so most jobs are a few minutes from Stud Park. From here it is a quick run up Stud Road to Knoxfield and Scoresby, east to Lysterfield and Ferntree Gully, across Wellington Road to Wheelers Hill and Mulgrave, and south over Police Road to Dandenong North and Endeavour Hills. Somewhere else nearby? Ring 03 9088 0246 and ask.
Plumbing problem in Rowville?
Talk to a licensed local plumber today. You will know what is wrong and what it costs before we start.